| 汽车座套安装方法 |
| 添加时间：2019/2/12 16:07:44 浏览次数： |
| 前靠背：首先是先拔掉头枕(一般按住头靠活动栓就可以解决);接着是把靠背套套好(看看前后左右套的是否正确);然后将靠背套正面从与座的接合地方塞到靠背反面，与靠背套背面底部的粘带稍用点力的固定好，这样会比较紧密;再将头套套好后插入靠背;最后将套好的靠背整理平整，前靠背安装完成。 Front-to-back: first, pull out the pillow (usually by holding the head on the movable bolt); then, cover the back cover well (see whether the front and back sleeves are correct); then insert the front side of the back cover from the seat joint to the back side, and slightly fix the adhesive tape at the bottom of the back of the back cover, which will be closer; then cover the head cover well and insert the back; finally, put the back cover well; The backrest of the machine is neatly arranged, and the front backrest is installed. 前坐位：先把座位套套在座椅上，并调整好位置(坐位前两角拉开);靠近靠背处有多余的部分及魔术贴和绳子直接沿着缝隙塞到靠背后面，并且把两边绳子尽量往两边底部拉出;座位侧面的绳子用力绑紧，再将魔术贴穿到座位底下前面座位下面两侧有两个工型扣，魔术贴打开来穿过开型扣用力拉紧反粘在白色底面;再将套好的座套整理平整，前座位安装完成。副驾驶座的安装和这个方法一样。 Front seat: First put the seat cover on the seat, and adjust the position (the first two corners of the seat open); close to the back, there are redundant parts and magic stickers and ropes directly along the gap behind the back, and pull the ropes on both sides of the bottom as far as possible; the ropes on the side of the seat are tightly tied, and then put magic stickers on the two sides of the front seat under the seat, magic buckles, magic buckles. Paste open to tighten and stick back on the white bottom through the open buckle, then tidy up the sleeve and finish the installation of the front seat. The installation of the copilot seat is the same as this method. 后靠背：先拔掉头枕，按下靠背的活动栓根据车的不同结构在拔掉头枕的方式不同;然后把靠背套套好，套时要分清上下部位，并且要放在正确位置;将后靠背套正面底部的橡皮筋塞到靠背后面，橡皮筋从下面串到后背后与上面的橡皮筋绑好，侧面橡皮筋和侧面橡皮筋绑好;再将套好的靠背整理平整，插入头枕，后靠背就安装完成了。 Back-to-back: First pull out the pillow, press down the movable bolt of the back-to-back according to the different structure of the car in the way of pulling out the pillow; Then put the back-to-back cover well, when the cover is set, the upper and lower parts should be distinguished, and put in the correct position; Put the rubber band at the front bottom of the back-to-back, the rubber band from the bwww.dianjiareguan.net.cnwww.yanglaoyuant.cnpenlinguan.37ix.com.cnweikuangg.37ix.com.cnuxing cao.37ix.com.cnwww.rerongjiaoji.org.cnottom to the back is tied with the upper rubber band, the side rubber band and the side rubber band. Tie the ribs well; then straighten out the sleeved backrest and insert it into the pillow, and the backrest is installed. 后坐位：后坐的座位一般的车稍稍用力往上拉一下，整个座位可以直接翻起，那么安装就相当简单了;首先把座位套套在座椅上，并调整好位置;把后端的座位前端的橡皮筋从座位下面拉到后面与后面橡皮筋绑住;再将后端的绳子抽紧绑紧;再将套好的座套整理平整，后坐位安装完成。Rear seat: The general car with the back seat pulls up slightly, and the whole seat can be turned up directly, so the installation is quite simple; first, the seat cover is put on the seat and the position is adjusted; the rubber band at the front end of the back seat is pulled from under the seat to the back and tied with the rubber band at the back; then the rope at the back end is pulled tightly and tightened; then the seat cover is tidied and leveled. Seat installation is completed. |
| 上一页 汽车各大零部件更换周期大全 |
| 下一页 汽车各大零部件更换周期大全 |
Copyright © 技术支持：遨游网络